easy no binding potholders

Easy No Binding Pot Holders Pattern/Tutorial

This is such an easy pot holder pattern to sew and customize to your liking! It’s great for personal use, to sell at craft shows, or to give as a handmade gift from the heart. These sets of pot holders have been one of my best sellers at craft shows. Everyone loves them! With step by step detailed instructions and tips, along with several pictures for guidance,  anyone can make these special potholders. There’s also a free downloadable PDF of the pattern instructions for your convenience.

(set of 2)

Materials

2 – 9 1/2″ squares for the front
2 – 9 1/2″ squares for the back
2 – 6″ x 2″ strip same fabric as the back
2 – 9 1/2 ” squares of insul brite (this is usually found in the store in the same place as the interfacing)
2 – 9 1/2″ squares of batting

Directions

Use your creativity to make this your own.  I make the front of the pot holders a lot of different ways – patchwork, applique, with a pocket, adding trim, etc.  Just make sure that you have a 9 1/2″ square when you’re finished.

It’s nice to have a helper.

I cut out one set with the front all one piece, and another set with four patchwork squares.  I cut the patchwork squares 5″ x 5″.  When I sew them together with a 1/4″ seam allowance, I will have a 9 1/2″ square.

Cutting Tip:  I used to cut out everything with my rotary cutter but I went through blades so fast that I stopped. Now I use my rotary cutter for the fabric, but for the batting and insul-brite I measure and draw the squares with a permanent marker, and cut it out with scissors.

This is the fabric that I’m using for this tutorial.  I like to use kitchen-like fabric for pot holders so I’m using herb packets and pots on a brown background for the front.  I like to use a heavy cotton twill or canvas for the back and loop.

First, fold the 2 strips in half lengthwise, right side on the outside and iron.  Then fold the lengthwise raw edges to the crease in the center.  Iron. With everything folded, raw edges on the inside, line up the outside edge and iron.

Edgestitch down both sides of the folded strips.

Tip:  I like to use my blind hem stitch foot so I have a guide for straight stitches.

Find the center of the front pieces along the top edge and baste a strip to the right side of each front making a loop.

Layer the fabric in this order, bottom to top.

  1. Insul brite, silver side down
  2. Batting
  3. Front, right side up
  4. Back, wrong side up

The fabric is layered this way so that the silver side of the insul-brite will be facing the outside on the back of the potholder where it’s needed.

Line up the edges of the layers and sew with a 1/2 inch seam allowance, leaving an opening in the bottom.

Tip:  Because there are so many layers I like to use my walking foot so that my fabric doesn’t stretch out, but it isn’t necessary.
Tip:  Another way to keep the fabric from stretching is to to use a heavier cotton like twill for the back and loop.  This is what I usually do, and with the heavier fabric on top, it eliminates the stretching.

Clip the corners.

Turn the pot holders right side out through the opening in the bottom.  Make sure to poke the corners out the best you can.

Iron the potholders and iron the opening on the bottom closed along the seam allowance.  The better this is ironed, the easier it is to sew.  Stitch the opening closed, close to the edge.

Topstitch around the entire pot holder.

Tip:
  If the feed dog won’t move the fabric forward when you start to sew it is probably because the presser foot isn’t level.  Just wedge something under the presser foot in the back to level it out.  There’s a tool that you can buy to do this but I just use whatever I have handy – usually sticky notes.

You’re done!

~~~~~~~~~~~~~~~~~~~~~~~~~~~

A couple of detail pictures.

 

 

 

 

 

For your convenience, download the PDF.

 

 

 

 

 

 

 

 

 

4 Comments

    • Renee

      Insul-brite gives added protection. It does more than a layer of batting because one side of the insul-brite reflects heat away from it. There will be protection on both sides, but it works better if the reflective side is facing the hot object. Thanks for your question!

  • Moree15

    What a great tutorial from WAY BACK in 2015… so glad I found it. I’m anxious to give these pot holders a try. Your directions and photos are exceptionally detailed and your personal tips are such a valuable bonus. Thank you for so freely sharing after you did all the work.

Leave a Reply

Your email address will not be published. Required fields are marked *